Fast & FREE Shipping!

This blog provides information for educational purposes only. Read our complete summary for more info.

May 10, 2023
Last updated

How to Make a Yeast Starter

Owner of Clawhammer Supply
Yeast Starter

An easy way to step up your brewing game and make better beer is to kick off fermentation with a yeast starter. There are a number of reasons you might want to make a starter - namely, increasing yeast cell count, ensuring yeast are healthy, and reducing lag time to get fermentation going right away. The more yeast cells there are, the more efficiently they can convert the sugars to alcohol. And the sooner fermentation begins, the lower the chance for contamination and off flavors. In short, fermenting with a yeast starter will improve the quality and consistency of your beer.

Equipment Needed


You'll also need a few ingredients to get the starter going. We're assuming that you're making a starter from a store-bought yeast packet. However, harvested and washed yeast can be used as well. Follow the same process. Also, dry malt extract can be purchased at any decent homebrew shop. Here are the necessary items:

  • 1 package of liquid yeast
  • 100 grams dry malt extract (DME)
  • 1200 ml Water
  • Yeast nutrient (optional)

Once all of the equipment and ingredients have been gathered, simply follow the steps below to make a yeast starter.

Yeast Starter Procedure

After you have the equipment and ingredients, it's time to make the actual yeast starter. Here's how it's done.

Step 1: Ask Yourself, If you Need a Yeast Starter

You make a yeast starter by first asking yourself, do I really need to make a yeast  starter? And you answer that question by reading the directions on the yeast package which will specify pitch rate.

STEP 2: Measure Water and Dry Malt Extract

Add 1500 ml of water to a pot, and set it to boil. While it’s heating, measure 150 grams of dry malt extract. This will create a starter with an initial gravity of 1.037, which is exactly where you want it. This is a bit more water and DME than a lot of generic recipes call for. I’ll explain why we’ve increased the amounts at the end of this article.

STEP 3: Add Dry Malt Extract and Boil

Once the water is boiling, cut the heat, stir it to create a vortex, and add the DME. Stir until dissolved then heat back up to a boil. You’ll hold the boil for a few minutes and then move on.

STEP 4: Clean and Sanitize the Flask

First clean and then sanitize it with a bit of StarSan. This part is really important because if you contaminate your starter it’ll also contaminate your beer. The bubbles are supposedly fine but I like to shake out as many as possible before moving on. Though, if you’re filming be careful with the camera angle during this part so you don’t become an internet meme.

STEP 5: Transfer Wort to Flask and Chill

Add the wort to the flask and then sanitize a bit of foil or a foam stopper and cover. Either put it in the refrigerator for 2 hours or into a bowl with ice water. Agitate to speed up cooling.

STEP 6: Pitch Yeast

Once the wort is room temperature, pitch your yeast. Our go-to yeast is White Labs since they have the best selection and our homebrew shop stocks a ton of different strains. Sanitize the package, shake well, again, being mindful of the camera angle, and add add to the flask.

Yeast Starter

I got a bit of yeast on the side of the flask so i’m going to throw on a glove, sanitize it, and shake flask to wash the yeast down into the liquid.

STEP 7: Add Stir Bar

This one is important. Toss the stir bar into some sanitizer then dump it out into your hand to make the biggest mess possible on the table. It’s important to constantly be marking your brewing territory and this is a great way to do it.

STEP 8: Cover Flask

Re apply the sanitized foil to your flask then dramatically whip out the sweet new Clawhammer Supply stir plate from your back pocket. Plug it in and marvel at the awesome new graphics before transferring the flask to the stir plate.

STEP 9: Allow to Ferment

Crank up the speed and leave it sit for 24-48 hours.

STEP 10: Pitch the Starter Into Wort

Once the starter has finished fermentation you can either pitch this straight into your beer, which is actually what White Labs recommends. Or you can put leave it sit so the yeast settles out, decant it by dumping off most of the liquid at the top, reincorporating the sludge at the bottom, then pitching this.

Yeast Starter Pro Tips

We've made a lot of yeast starters. Here is some advice based on the mistakes we've made!

Don't Boil in a Flask

Don't boil your ingredients in a flask. The bottleneck of flasks greatly increases the risk of boil over. This potential is compounded on electric burners which cycle intense heat on and off. If you're worried about boil over, use a sauce pan to boil the ingredients and then transfer into a sanitized flask after.

Use a Calculator

Use a Yeast Starter Calculator to ensure that the proper amount of yeast cells are created and they're grown in a way that produces healthy, unstressed yeast. Most generic yeast starter recipes call for 100 grams of DME and 1 liter of water. Though these standard amounts were created when the standard size for liquid yeast packages was half the size that it is today.

Pitching new, 150 billion cell yeast packages into a starter made to those specifications will result in a high innoculation rate and a lowered growth factor. For this size of packaging, we like to bump the amounts up up to 1.5 liters and 150 grams of DME. If you're unsure how much water and DME to use for a starter, check out our favorite online yeast starter calculator.

Kyle Brown is the owner of Clawhammer Supply, a small scale distillation and brewing equipment company which he founded in 2009. His passion is teaching people about the many uses of distillation equipment as well as how to make beer at home. When he isn't brewing beer or writing about it, you can find him at his local gym or on the running trail.

  • Where can you find the yeast on your page? I looked under products and didn’t see it.

    Posted by Lee on September 26, 2019
  • Hello , after i have done my starter how do I actually make a beer with it?

    Posted by Presley on September 01, 2019
  • I forgot to mention that I used no other yeast product. So if I was making it for a distilled spirit I would still use no other yeast product. Does that sound doable?

    Posted by Sister Janet on December 05, 2017
  • I have made a starter for bread using organic grapes and water. I am wondering if one could make a stater for wine/beer/spirits from the same. Does anyone have an opinion? I got my starter recipe from Nancy Silverton’s Book on La Brea Bread Baking book.

    Posted by Sister Janet on December 05, 2017
  • You sure can brutha! I do it a lil different but same concept. As the wort is cooling I take a liter and put it in a separate jar. Once it is cooler (120-80°f) heat up 100ml of purified water to 120°f. Mix in 5-7g of GOFerm. Once that has mixed and dropped to 104°f put your yeast in (I use 10g of yeast). Let the yeast rehydrate for 20-25mins then put in 500ml of your wash. It is very important however to make sure there is less than an 18°f difference between yeast starter and wash when mixing them. After a couple hours I pitch the starter I just made into my main batch making sure they are within 18°f of each other.

    Posted by Drunk on October 26, 2017
  • First at all, thanks for all the help that we can find on this site very useful and hopefully would buy destiller cooper on the future….. I have a question? Can I make starter yeast with dry active yeast instead of using liquid yeast? Thanks

    Posted by ricardo on August 14, 2017

Leave a comment

Please note, the design of our website does not allow us to respond directly to blog comments. Please email us directly regarding questions about products. We don't answer questions about recipes, procedures, etc. However, feel free to leave a comment or respond to comments made by others!