10 Gallon Steam Condensing Lid Kit Manual

Questions: support@clawhammersupply.com.

Here's how we run the 10 Gallon Steam Condensing Lid Kit on brew day, on both our 120V and 240V systems. It pulls the steam out of your boil and turns it back into water, so you're not filling your brew space with steam. It also cuts your boil-off about in half.

1. What's in the kit

The kit ships in parts. Put it together before your first brew day.

  • Domed lid
  • Tee and spray valve
  • All the fittings, tri-clamps and hoses you need
  • Submersible pump
  • Two 1/4" NPT plugs and a roll of thread tape for the lid
  • Heat resistant gloves

2. What you'll need

  • Two 5+ gallon buckets: one full of cold water for the pump, one to catch the drain water
  • Our counterflow chiller. You can't use a hop basket with this lid, so your hops go right into the kettle, and loose hops will clog our flat plate chiller.

3. Two safety rules

  • No clamps. The kit doesn't come with clamps, and if you have our lid clamps, leave them off. The lid needs to be able to vent if the drain ever gets blocked.
  • Water before heat. Never run the heat with the steam lid on and no water flowing. Turn the pump on as soon as the lid goes on, and at the end of the boil, turn the heat off before the pump.
WARNING: HOT STEAM. The lid, the fittings and the drain water get hot enough to burn. Before you open the 3" cap, turn the heat off, wait 30 seconds, put the gloves on and keep your face and arms back.

4. Before brew day

  • Put the lid together (see Assembly).
  • In your brewing software, cut your boil-off rate in half.

5. Assembly

Put it together on the domed lid before the lid goes on the kettle, while everything's cold. Every tri-clamp joint gets a gasket.

  1. Plug the lid. Add the included thread tape to the 1/4" NPT plugs and screw them into the small ports on the lid.
  2. Hop tee. Attach the tee with the 3" hop hole to the center of the domed lid with a tri-clamp and gasket. Clamp the clear 3" cap on the hop hole.
  3. Condenser tee. Attach the other tee to the hop tee's side arm, with the longer end facing down.
  4. Spray valve. Attach the spray valve fitting (the 1.5" tri-clamp fitting the water comes in through) to the top of the condenser tee, with the spray head facing down.
  5. Drain. Attach the reducer to the bottom of the condenser tee with a tri-clamp and gasket, then push the silicone drain hose onto it.
  6. Water line. Cut the 3/8" hose to length with the included cutter. Attach the push fit connector to the spray valve fitting and press one end of the hose into it. Screw the included hose fitting into the pump, then push the other end of the hose into it.
  7. Pump. Put the pump in a bucket and fill it with cold water or ice water.
The steam condensing lid put together on a 10 gallon kettle
The steam condensing lid put together on a 10 gallon kettle.

6. Set up

  • Fill one bucket with cold water and set the submersible pump in the bottom.
  • Run the drain hose to the second bucket. Keep it running downhill with no loops.
  • Keep the end of the drain hose above the water so it drips freely. A loop in the hose or an end under water backs the steam up, and it comes out at the lid seam.

7. Bring it to a boil

  • On the 120V, heat to a boil at 100% with your normal brewing lid on, cracked a bit like normal.
  • On the 240V, you can boil with the lid off.
  • Once it's boiling and the hot break is done, take the normal lid off.
  • If you have a 60 minute hop addition, add it now.

8. Put the steam lid on

  • Set the steam condensing lid on. Don't clamp it.
  • Turn the pump on right away.
  • Turn the power down to the steam lid setting below.

9. Power settings

Here's the % of power we use on our 10 gallon systems.

System Heating up Hot break Steam lid on
120V 100% 100%, normal lid cracked About 70%
240V 100% 55%, lid off 20–25% to start
  • Tune it from there. You want a rolling boil and no steam at the lid seam or coming out of the drain hose.
  • Keep the water coming out of the drain hose under 140°F.
  • If you see steam, or the drain water is running hotter than that, turn the power down a little or make sure your cooling water is cold and full.

10. Keep an eye on the water

  • Top up the cold water bucket so the pump never runs dry.
  • Pro tip- add ice to the cold water bucket to make it last longer.

11. Adding hops

The steam under the 3" cap is hot, so take your time.

  1. Turn the heat off and wait 30 seconds.
  2. Put your gloves on. Keep your face and arms away from the opening.
  3. Take off the 3" cap and add your hops.
  4. Put the cap back on and turn the heat back on.

12. End of the boil

  • Turn the heat off first, then the pump.
  • Chill with the counterflow chiller, not a plate chiller.
  • Save the drain water for cleaning up at the end of the brew day. It's hot, and it's not for brewing.